Did you know?

Dec 29, 2023 ... Disclaimer/Disclosure: Some of the content was synthetically produced using various Generative AI (artificial intelligence) tools; so, ...FiOS won't reset after power outage. 08-23-2011 06:12 AM. Hello, I've been a FIOS TV, Internet, and phone customer for about a year. Our power went out last night for about 15 minutes, and all 3 of our FIOS services are still not back up and running. The battery backup unit displayed a red battery light and was beeping throughout the night.Step 1A: Make the connections. Connect the coax cable from the coax port on your router to a coax outlet. (Required for Fios TV*) Connect the power cord to your router then to an electrical outlet. Router will take up to 10 minutes to update completely. Move to the next step when the front light is solid white.My cable box keeps resetting when ever the computer is on. I get an LDR code on the box, resets, I have to press menu to get the cable back on and then the reset screen loads. It will continue to reset every 10 minutes or less until the computer is shut off.The more frustrating problem is that I can't watch any recorded programs. The dvr says the program is playing, but it stays on the current channel. During this error, the stb won't record any programs. The only way to fix it is to reset the stb. Once reset it works fine for a while, but the problem eventually comes back.Step 2 - Connect your existing Fios router to your ONT via Ethernet. Skip this step if your ONT is already connected to your router using Ethernet. In a later step, we're going to switch the ...Menu button. simultaneously for 6 seconds. Release the buttons to enter pairing mode. A red LED will blink above the Volume Up button on the remote. Allow up to a minute for the process to complete. For additional info, see this Stream TV support page. Here's how to place the Voice Remote for your 1st-generation Stream TV into pairing mode.If your Spectrum cable box is non-responsive and the on-screen menu is not accessible, a manual reset may be necessary. Here's how: Locate the power cord at the back of your cable box and unplug it from the power outlet. Wait for at least 30 seconds to ensure the box fully powers down. Plug the power cord back in and wait for the box to ...New fios boxes installed by technicians -internet working but tv not showing channels? Pressing ONT reset button will fix it?Restart your cable box using a remote control by navigating to the cable box menu and choosing the restart or reboot …Step 2 – Connect your existing Fios router to your ONT via Ethernet. Skip this step if your ONT is already connected to your router using Ethernet. In a later step, we’re going to switch the ...It's difficult to answer your question without some basic information like what symptoms are happening, are you restaring the STB or is it restarting itself, etc. 03-18-2013 02:47 PM. Hello andchang74, Make sure all wires are securely attached to the set top box. Perhaps your coax cable is loose or damaged.Unplug the box from power. Unpair the FiOS one remote from the box by pressing the play/pause button and the zero button until the LED on the remote blinks blue. Let it keep blinking until it blinks red. Then plug back in the box and keep pressing the menu button on the remote while pointing it at the cable box.Simple ventilation or signal problems can cause cable boxes to reboot. Cable boxes can inexplicably reboot while being used, while on standby or after power outages. While it may surprise a user if a cable box reboots without user interaction, the reasons are as simple as power surges, overheating or temporarily degraded signal quality.180K views 8 years ago. Many Verizon Fios TV problemTold Verizon they need to disable it or upgrade the software to To reset your Set-Top Box, hold the button for 15 seconds or unplug the equipment for 10 seconds and then plug it back in. Do this for all of your Set-Top Boxes. Notes: To avoid problems with your FiberOptic TV service, make sure your router is plugged in and turned on at all times. Even if you are not currently using the Internet, your router ...Reboots will often solve issues by resetting the box and its cable connection. To reboot, unplug the cable box from the power, either from the back of the box or from the power outlet on your wall or power strip, for approximately 30 seconds, and then plug it back in. This will begin the boot-up process. Wait for picture and sound to return ... Disconnect the Battery. Wait for about 2 minutes. Reconnect th After an hour on the phone they are going to replace the DVR..... Just a suggestion: If you haven't already done so, try pulling the power plug on the DVR, wait 20-30 seconds, plug it back in and let it go through the startup, then see if your recordings show up and the other stuff works. How to program your remote control · Turn on your TV and

One warning though, enabling passthrough mode disables Wi-Fi on the gateway, so only do this if you have a computer with an Ethernet port and cable so you can get to the gateway's settings that way. Verizon 5G Home Internet Gateway ASK-NCQ1338FA web interface. Still others have said that passthrough mode causes the reboots. In that case, try ...Check here: Main Menu > Customer Support > Top Support Tools > Replace Fios Remote > Replace Fios RemoteI have a digital set-top box with the DVR built in. The thing that the box is doing is when switching from Non-HD channels to HD channels, you have to turn the box off so it will reset and then turn it back on. It seems while you are switiching channels within Non-HD channels it works fine and the same with switching channels within the HD ...24/7 automated phone system: call *611 from your mobile. Here's how to factory / hard reset your LTE Broadband Router if the screen freezes or call, app, audio or sync issues occur.

2.0b/ WI-FI INSTALLATION. Place the Verizon Wi-Fi Extender directly next to the Verizon Router. Take the Ethernet cable from the packaging and connect one end to the LAN port on the Router and the other end to the LAN port on the Extender. Connect the power cord to your extender then to an electrical outlet.I have a digital set-top box with the DVR built in. The thing that the box is doing is when switching from Non-HD channels to HD channels, you have to turn the box off so it will reset and then turn it back on. It seems while you are switiching channels within Non-HD channels it works fine and the same with switching channels within the HD ...Box keeps freezing. 10-26-2019 08:13 AM. Here is my problem: all of the Verizon Fios equipment is in our basement. The main cable box is on the second level and the other box is on top floor in the bedroom, which is the problem. The main box is a bigger box and the bedroom is smaller. Even though the box in the bedroom is connected with coaxial ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Program a DIRECTV universal remote for an HD DVR or HD re. Possible cause: The battery is only needed to provide backup power for telephone service..